Knowledge of wooden door installation.
1.
Installation condition.
(1) the installation method of reserved holes must be adopted for wooden doors, and the practice of laying holes while installing them is strictly prohibited.
(2) the wooden door shall be installed after the installation of the floor works of the installation hole (such as floor tiles and stone), and at the same time after the wall putty has been scraped and polished (the wall needs to be affixed to the hole of the wall brick and stone, all must be affixed to the side of the hole), before the installation operation can be carried out.
(3) the humidity of the wall at the entrance of the installation hole is less than 25%. If the humidity is more than 25%, a moisture-proof isolation layer should be made on the installation wall.
(4) the environment of the installation site is clean, no clutter and no cross operation.
2. installation tools electric hammer, woodworking hammer, plane, flat file, fine tooth saw (hacksaw), screwdriver, angle ruler, tape measure, wire hammer, horizontal ruler, electric drill, hole opener, stamp, corresponding specification bit.
3, installation material iron sheet connector, 60 iron nails, 25 and 20 self-tapping screws, 502 glue, towel or cotton yarn, wood cutting, small wood strips, pig hair brush, styrofoam, latex, door lock, hinge, door suction, wall moisture insulation material.
Second, the installation sequence of wooden doors.
1. Assemble the door cover.
First find out the door cover and the vertical plate, align the seam according to the number on the back, and apply glue at the interface on the same plane.
2. Install the door cover.
Put the firmly assembled door cover as a whole into the door hole, roughly fix the door cover around with a small wooden bar, and the two sides of the door cover should be on the same plane as the wall, then check whether the door cover as a whole is perpendicular to the ground, whether the two corners of the door cover roof and the two vertical plates are at right angles, and whether the door cover vertical plate is bent or not, twist the iron sheet at both ends to wrap it around the wall.
3. Install the door leaf.
First open and close the page slot, the distance between the hinge slot and the two ends of the door leaf should be 1 / 10 of the height of the door leaf.
4. Install the door lock.
After installation, it is necessary to check whether the door leaf and door lock switch is flexible, whether the seam is flexible, and whether the seam is in accordance with the specification.
5. Install door cover line.
Cut the door cover line with right-angled edge into a 45-degree angle, trim it with woodworking plane, insert the right-angle edge into the door cover slot, and glue the door cover line with the door cover board with floor glue.
6. Install the door stopper in the corresponding position.
Third, installation skills of wooden doors.
When installing the wooden door, * * check whether each part of the wooden door is complete, whether the size of each part is correct, and whether the corresponding position assigned to each set of doors is consistent with the doorway ruler.
The installation techniques of wooden doors are as follows:
1. Please place the goods horizontally on the ground and do not lean against them.
2. Unpainted products should be painted within five days.
3. Try to avoid outdoor sunlight for a long time to prevent the wooden door from being heated.
4. Keep indoor air circulation to prevent the wooden door from getting damp frequently.
5. To prevent the wooden door from being impacted abnormally, it should not be forced too hard when it is not closed.
6. It is strictly forbidden to nail heavy objects on the door.
7. Before installing the corner wall and T-wall doorway, the customer should be informed that the "fake wall" should be made on the side without the door stack, the width size is not less than 50mm, and the width size of the "false wall" should be determined according to the width of the line, otherwise, the door edges displayed on both sides are asymmetrical.
8. The reserved dimensions of single-fan flat door, sub-master door and double opposite door door are (the thickness of cover plate is 32mm): door height = door height + 40mm, door width = door width + 65mm.
Other types of composite doors vary according to specific conditions (note: the height of the doorway refers to the net height, width and thickness of the doorway from the ground project that has been done).
How to supervise the installation of wooden doors.
The main results are as follows: 1. The mining mouth is consistent and not misplaced.
2. The door leaf and lock switch is flexible.
3. The gap between the left and right sides of the door leaf is the same.
4. The door cover plate should be perpendicular to the ground level and there is no bending phenomenon.
5. The door cover line is close to the surface of the wall.
6. There is no damage to the decorative surface.
7. Clean the full set of solid wood doors after they have been installed, and teach users to check and accept them.
400-189-9797
